Wrought iron
Wood & steel frame
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Dallas?
In Dallas, TX, gate parts and welding work typically runs between $160 and $550 for most repairs, with full gate fabrication or structural welding falling between $800 and $3,200 depending on the scope. A standard weld repair on an iron driveway gate in Dallas usually lands around $250 to $400, while replacing a gate actuator (the motorized arm that physically pushes the gate open) runs $400 to $900 installed. We quote every job in writing before any work starts, so the number you’re given is the number you’ll pay.
This pricing guide breaks down exactly what gate parts and welding work costs in Dallas in 2026, so you’ll know what’s reasonable before you pick up the phone. If you’d rather skip the reading and get a straight answer, call us at (325) 225-5440 and a live person will talk through your specific gate with you right then.
Key Takeaways:
- Most gate part replacements in Dallas cost $160 to $550 including labor
- Structural welding or fabrication work runs $800 to $3,200
- Every Portcullis job includes a written price before work begins and a written 365-day guarantee
- Calls are answered by a live person 24/7, including holidays
- Free estimates: call (325) 225-5440
Gate Parts & Welding Cost Breakdown (2026)
Here’s what our technicians across Dallas, from Preston Hollow to Lake Highlands and down through Oak Cliff, are charging for common gate parts and welding work in 2026. These are real numbers from the field, not national averages.
| Service | Typical Dallas Price Range | What’s Included |
|---|---|---|
| Weld repair (cracked gate frame, broken picket) | $160 – $350 | On-site welding, grinding, rust-inhibiting primer |
| Hinge replacement (welded, heavy-duty) | $225 – $450 per hinge | Old hinge removal, new hinge installed, gate re-leveled |
| Swing gate actuator replacement | $400 – $900 | New actuator, mounting hardware, travel adjustment, testing |
| Slide gate roller and track repair | $250 – $600 | Replacement rollers, track repair or section replacement |
| Gate operator circuit board replacement | $300 – $750 | New control board, programming, safety sensor verification |
| Full weld-on gate frame reinforcement | $500 – $1,200 | Steel plate or angle iron reinforcement, weld pass, primer |
| Custom gate fabrication (standard driveway size) | $1,800 – $3,200 | Design, steel, welding, primer, installation |
| Emergency weld repair (same-day callout) | $200 – $450 | Immediate response, temporary stabilization, permanent repair quote |
Those ranges reflect what we see across the Dallas market in 2026. A gate in University Park with decorative scrollwork will run higher than a simple chain-link or tubular steel gate in Mesquite or Garland. What pushes costs up or down?
Factors that raise cost:
- Decorative iron work that requires precise TIG welding instead of standard MIG
- Gate weight above 600 pounds (common with solid-stave cedar or heavy ornamental steel gates)
- Seized or corroded hardware that adds removal time
- Properties in Dallas neighborhoods with HOA-specific design requirements
- Electrical work tied into the gate operator (conduit runs, new low-voltage wiring)
Factors that lower cost:
- Parts that are still in production and carried on our trucks
- Weld repairs done before rust has spread (a hairline crack is cheaper to fix than a snapped frame)
- Access to the work site (no fence line clearing, no tool hauling across a large property)
- Gates with standard mounting patterns that don’t need custom brackets
We’re an independently owned Kingswell company, which means the price we give you in writing is the price on your invoice at the end of the job. No adjustment after the technician has the gate disassembled. The Kingswell Way isn’t a slogan; it’s five commitments we were founded on in 2008: say the price before the work, show up in the window we gave, leave the place cleaner than we found it, put the guarantee in writing, and come back if it fails.
What Affects Gate Parts & Welding Pricing in Dallas
Dallas is a big market with a lot of gate styles, and pricing reflects the specifics of what you’ve got on your property. Here’s what actually moves the number.
- Gate material. Mild steel is the least expensive to weld and repair. Wrought iron and custom ornamental steel require more skill and finer equipment, which adds cost. Aluminum gates need special welding rods and oxidation control, and that’s reflected in the price.
- Gate size and weight. A 12-foot driveway gate weighs anywhere from 350 to 800 pounds depending on the material. Heavier gates require more powerful actuators, heavier hinges, and more manpower to reposition during a repair. Labor gets billed honestly, and a 700-pound gate takes longer to work on than a 200-pound walk gate.
- Age of the gate system. Dallas heat accelerates rust in coastal-adjacent air and well-struck joints, and older gates tend to have layered repairs from previous vendors. If we’re working around someone else’s failed weld or a corroded bracket that’s been painted over, that adds time.
- Accessibility to the weld site. Working at the bottom hinge of a gate in a narrow easement with a brick wall on one side takes longer than an open work area. If our truck can’t reach within 75 feet of the gate, that changes labor.
- Time of year. Dallas summers run hot, and our technicians weld in 100-degree heat with full safety gear. Emergency calls during the brutal July and August afternoons may carry a small premium for the conditions, though we’ll always tell you that before dispatch.
- Permit or code compliance. Some Dallas-adjacent municipalities, including Highland Park and University Park, require gate setbacks and height restrictions that affect what parts and modifications are legal. We handle that compliance, but it can affect scope on installation or major structural work.
How Much Does Gate Welding Cost in Dallas Specifically?
A standard weld repair in Dallas runs $160 to $350, and that covers most cracked frames, broken pickets, and hinge re-welds. If the failure is structural, like a failed gate post or a frame that’s dropped and dragging, you’re looking at $500 to $1,200 for reinforcement or section replacement.
In neighborhoods like Casa View or Buckner Terrace where gates see heavy use on daily commutes, we often see bottom-hinge weld fatigue. The bottom hinge takes the entire weight of the gate every time it cycles, and in Dallas clay soil that shifts with summer drought and spring rain, gate posts can lean over time and transfer stress to the weld points. That’s a common fix for us, normally landing in the $200 to $400 range when caught before the post itself fails.
For more detail on what we handle, see our Gate Parts & Welding in Dallas page.
What Does It Cost to Replace Gate Hardware vs. Welding It?
Sometimes welding is the right fix, and sometimes replacing the part is smarter and cheaper in the long run. Here’s the honest breakdown.
When welding makes sense: A cracked weld on a steel gate frame, a broken decorative picket, a loose bracket that’s still structurally sound. Welding restores the original strength and costs $160 to $350 in most cases.
When replacement makes sense: A hinge that’s worn through, a bracket that’s bent beyond straightening, a gate wheel with a seized bearing. Replacement parts for these run $25 to $120 for the part and $100 to $300 for the labor, so the total typically lands between $150 and $420.
Our technicians will tell you which direction is right before starting anything. If welding a hinge costs $275 and replacing it costs $200, we’re going to recommend replacement every time. That’s just the Kingswell Way: say the price before the work, and say what’s actually best for the gate, not what’s easiest for us.
Gate Operator Parts: Costs for the Electronic Side
Gate actuators, control boards, safety sensors, and remote receivers are the parts most likely to fail in Dallas’s climate, and they’re also the parts where pricing surprises most often show up. Here’s what you should expect in 2026.
Swing gate actuator (the motorized arm): $400 to $900 installed. The actuator itself runs $180 to $450 depending on brand and weight capacity, and labor runs $100 to $250 including mounting, travel adjustment, and testing. We stock and service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so our technicians arrive knowing the specific system on your property.
Control board replacement: $300 to $750 installed. Boards are $120 to $500 depending on the operator make, and programming and safety verification run $80 to $200. A board failure is often misdiagnosed as a bad actuator, so we always test the complete circuit before recommending a replacement.
Safety sensor (photo eye) replacement: $120 to $250 installed. In Dallas, sensors take a beating from UV exposure and sprinkler overspray. A misaligned sensor that’s been hit by a lawn mower or a Texas hailstorm is the most common call we get after a Dallas thunderstorm.
Remote transmitter programming or replacement: $60 to $180. Simple programming is quick. Replacement remotes run $35 to $90, and reprogramming a multi-button remote for a gate plus garage door runs $50 to $100.
Warning: Gate operators involve electrical components and, on swing gates, high-tension torque. If you’re testing a gate operator and the gate is jerking or stalling at one point in its travel, that’s not something to force. Stop running the gate, pull the manual release if you know how, and call us at (325) 225-5440. A trained technician can diagnose the problem safely without risking an uncontrolled gate swing.
How to Save on Gate Parts & Welding
You don’t need to overpay for gate work, and you also don’t need to gamble on the cheapest handyman who may or may not show up. Here’s what actually saves money in Dallas.
- Catch problems early. A hairline crack in a gate frame weld is a $200 fix. A snapped frame that’s been dragging for three months is a $1,200 fix. If your gate is sagging, grinding, or shaking when it opens, that’s your signal to act.
- Know your gate operator brand before you call. The brand name is printed on the actuator housing or the control box. Knowing you have a LiftMaster or a FAAC means we can bring the right parts on the first trip, which saves labor hours.
- Ask for the written price up front. If a gate company won’t put the price in writing before starting work, find a different company. This is the single most effective way to avoid after-the-fact markups. Every Portcullis job includes a written price before a single bolt is turned.
- Consider bundling repairs. If you need a hinge re-weld and your actuator is original to the gate from 2011, doing both in one trip saves a dispatch fee and a second service call window.
- Use a company that guarantees the work in writing. Every Portcullis repair carries a 365-Day Done Right Promise. If the repair fails within that period, we come back and fix it at no charge. That’s a written guarantee stamped on every invoice, and it means you pay once, not twice.
For a free estimate on any gate parts or welding work in Dallas, call us at (325) 225-5440 and we’ll talk through your gate over the phone. No dispatch fee for the phone call, and no obligation.
FAQs – Gate Parts & Welding Cost
How much does it cost to weld a gate in Dallas?
Most gate weld repairs in Dallas run $160 to $350, with structural frame reinforcement running $500 to $1,200. A simple crack in a steel gate frame is typically a same-day repair at the lower end of that range. Call (325) 225-5440 for a free estimate with a written price before any work starts.
Is it cheaper to weld a gate or replace the broken part?
Welding a cracked bracket costs $160 to $350, while replacing that same bracket costs $150 to $250 in most cases. If the part is bent, corroded, or previously welded by someone else, replacement is usually the smarter money. Our technicians will tell you which direction is right for your specific gate before starting any work.
How much does a gate actuator cost in Dallas?
A swing gate actuator replacement in Dallas runs $400 to $900 installed, including the part, mounting hardware, travel adjustment, and testing. The actuator itself is typically $180 to $450, with labor running $100 to $250. We service nine major brands, including LiftMaster, FAAC, BFT, and Linear, so the technician who arrives already knows your system.
Can you fix a gate the same day in Dallas?
Yes, most weld repairs and common parts replacements are completed in one visit, and we answer calls around the clock with a live person. Dallas gate failures happen at unpredictable hours, and a broken gate is a security problem as much as a convenience one. Call (325) 225-5440 and we’ll give you a real arrival window, not a four-hour spread.
Do you guarantee your gate welding work?
Yes. Every repair we do carries a written 365-Day Done Right Promise. If the repair fails within that period, we return and correct it at no charge. That’s the Kingswell Guarantee, and it’s stamped on every invoice. A repair that fails six weeks later is not something you should have to pay twice to fix.
How much does emergency gate repair cost in Dallas?
Emergency same-day gate repair in Dallas runs $200 to $450 for the initial stabilization and repair, with complete structural fixes priced separately in writing. We don’t inflate the price because you’re in a bind. The emergency premium covers the immediate dispatch and after-hours labor, not a made-up number. Call (325) 225-5440 any time, day or night, and a live person will answer.
The Kingswell Guarantee on Every Gate Parts & Welding Job
Portcullis Gate Repair Dallas is an independently owned Kingswell company, and we’ve operated that way since 2008. Every Kingswell location, including ours, is bound to four promises on every job:
- A written price before any work starts. You see the number and approve it before we touch a bolt.
- A real arrival window. Not “sometime between 8 and 5.” We give you a window we actually keep.
- A clean job site. We leave your driveway the way we found it, minus the broken gate parts.
- A written guarantee on the repair. 365 days, stamped on the invoice, including a free return visit if the repair fails.
Dean Prescott runs this Portcullis location, and the standard here is the same standard we’ve held since 2008. Background-checked technicians in uniform, live phone answers 24 hours a day, and a price you agree to in writing before the work begins. Not a franchise promise, a written one.
For gate parts and welding work in Dallas, from North Dallas to Oak Cliff, call us at (325) 225-5440 for a free estimate. We’ll talk through what’s failing, give you a real price range, and set a real arrival window. If you’d like to learn more about the work before calling, start with our home page or the Gate Parts & Welding in Dallas page for the full scope of what we handle.
Pricing reflects the Dallas market as of 2026. Portcullis Gate Repair Dallas offers free estimates – call (325) 225-5440.
Written by Dean Prescott, Owner at Portcullis Gate Repair Dallas, serving Dallas since 2008.
What Our Customers Say
"Electric gate kept doing its own thing, opening at random. The tech found a shorted sensor and a worn board, fixed both, and showed me the old parts. Price was what he quoted on the phone."
- Cassandra Pike"Our intercom and gate motor both quit. They fixed the whole system in one visit and explained the warranty clearly. On time, polite, and tidy. Can't ask for more."
- Yvette Marchetti"Hinge sheared off our heavy iron gate. They welded a new one on and it's sturdier than before. Showed up on time and cleaned the driveway after the welding."
- Rhonda Mikula